產品介紹   

首頁 > 産品中心 > 減速機

PH系列行星減速機

產品特點:

概要


輸出額定力矩

T2N : 14 Nm - 2000 Nm


減速比:

單節 :3 / 4 / 5 / 8

雙節 :12 / 16 / 20 / 25 / 32 / 40 / 64

参節 : 80 / 100 / 125 / 160 / 200 / 256 / 320 /512


低背隙

單節 : ≤10arcmin

雙節 : ≤18arcmin

叁節 : ≤22arcmin

單節 : ≧ 97%

雙節 : ≧ 94%

参節 : ≧ 92%

容易安裝

低噪音

結構緊湊


尺寸

PH240 / PH285 /PH330 / PH400 


減速機性能資料


減速機性能資料

減速機性能資料


開機前的註意事項

Matters that need attention before shutting down

出廠時已按規定量加入洞滑油,因此到貨後可直接使用。

首次運轉時,請先確認輸出軸的轉向,然後逐漸增加負荷。

Thespeifed amount of Lincant has been added before deivery so the machine can be used diredty when arived.

Confim the olling direction of the output shaft and increase the load gradually the frst tme operating.


每日檢查

Daily check

運轉中減速機外殼溫度有無異常上升? (最高不大於90C)

軸承、齒輪等部位有無異響?

減速機有無異常振動? 1 出現此類異常時,請立即停機並聯系我公司。)

有無潤滑油漏油? ( 出現油脂泄漏時,請聯系我公司。)

Whether the temperature of the reducer shell eises

abnomally?0Maxmum 90 degreel

Are there any abnomal condtions on adetrees or chain wheels? is the reducer vibrating abnommally? 0f i happens, please shut down the

machine and contact our company)

is the lubicant eaking? (Hf it happens, please contact our company)


運轉中的註意事項

Matters that need attention during operating

請註意不得過載。

輸出軸的轉速不得大於規定轉速。

出現以下情況時, 請停機檢查。

1、溫度突然開始升高。

2、突然發出很大異響。

3、轉速突然開始不穩定。

可能的原因如下,請及時處理。

1、是否處於過載狀態?

2、軸承、齒輪、傳動面有無損傷?

3、機器連接條件有無異常?

Do not overboaded.

The rlling speed of the output shaft should not be faster than the

spedfied one.

Please shut the machine down when folowing situaton shows.

1、The temperature rise suddenly.

2、Strange noise are emerged.

3、The oing speed becomes unstable.

The possible reasons are as fllows., and please make sure to deal with

it in time.

1、Whether it is overloaded or not?

2. Ave the axletrees, gear wheels and the oling side damaged?

3、Is the connecting condition aboomal?


定期檢查

Regular check


有無過載狀態,有無異常旋轉?

皮帶輪、鏈輪、減速機安裝螺栓等有無松動?

主要部件的檢查與維護。( 出現異常現象時,請立即停機並聯系我公司。)

Whether it is overloaded or rling abnomaly?

Is the belt pulley. chain wheel. the Insalltion bot of the reducer loose?

The check and mainterance of main components. (When there is an abnomal phenomenon, please shut down the machine. and contact our cormpeany,) .


潤滑油管理

The lubricant managing

油脂不能更換。

The grease can not be replaced.